Ubuntu 拦截并监听 power button 的关机消息

举报
小麦大叔 发表于 2021/12/29 23:06:12 2021/12/29
【摘要】 system:ubuntu 18.04 platform:rockchip 3399 board:NanoPi M4 前言 物理上的电源按键短按之后,系统直接硬关机了,导致应用程序无法保护现场,就直接...

system:ubuntu 18.04
platform:rockchip 3399
board:NanoPi M4

前言

物理上的电源按键短按之后,系统直接硬关机了,导致应用程序无法保护现场,就直接宕机了,查阅了大量资料,发现通过使用acpi可以禁止这个关机消息上传,但是看完acpi就放弃了这个想法,至少我在arm平台上没有具体成功实现这个消息的拦截,不然通过这个方式应该很便利,至少在intel上问题不大。

解决方法

google上搜索了很久,加上实践测试,终于找到了解决方案,具体如下所示;

Instead, adding a single line to /etc/systemd/logind.conf was enough to do the trick:
#HandlePowerKey=poweroff
HandlePowerKey=suspend
Now, pressing the power button causes instant suspend.

修改/etc/systemd/logind.conf文件,找到HandlePowerKey,并且可以使用下面几个参数:

  • suspend 系统会被挂起,如果我的设备终端有屏幕,而且装了相应的桌面,还会进入锁屏界面;
  • ignore 电源按键的消息会被忽略,即我按下按键之后什么事情都没有发生;

监听按键

cat /proc/bus/input/devices

  
 
  • 1

得到如下结果:

I: Bus=0019 Vendor=0000 Product=0003 Version=0000
N: Name="Sleep Button"
P: Phys=PNP0C0E/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
U: Uniq=
H: Handlers=kbd event0 
B: PROP=0
B: EV=3
B: KEY=4000 0 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
U: Uniq=
H: Handlers=kbd event1 
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
U: Uniq=
H: Handlers=kbd event2 
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

  
 
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29

所以,可能需要监听event1或者event2,可以通过以下的代码直接监听事件的输入信息;

#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <string.h>
#include <sys/types.h>
#include <fcntl.h>
#include <errno.h>
#include <time.h>
#include <linux/input.h>
 
struct input_event event;
 
int main(int argc, char **argv)
{
    char          name[64];           /* RATS: Use ok, but could be better */
    char          buf[256] = { 0, };  /* RATS: Use ok */
    unsigned char mask[EV_MAX/8 + 1]; /* RATS: Use ok */
    int           version;
    int           fd = 0;
    int           rc;
    int           i, j;
    char          *tmp;
 
#define test_bit(bit) (mask[(bit)/8] & (1 << ((bit)%8)))
 
    for (i = 0; i < 32; i++) {
        sprintf(name, "/dev/input/event%d", i);
        if ((fd = open(name, O_RDONLY, 0)) >= 0) {
            ioctl(fd, EVIOCGVERSION, &version);
            ioctl(fd, EVIOCGNAME(sizeof(buf)), buf);
            ioctl(fd, EVIOCGBIT(0, sizeof(mask)), mask);
            printf("%s\n", name);
            printf("    evdev version: %d.%d.%d\n",
                   version >> 16, (version >> 8) & 0xff, version & 0xff);
            printf("    name: %s\n", buf);
            printf("    features:");
            for (j = 0; j < EV_MAX; j++) {
                if (test_bit(j)) {
                    const char *type = "unknown";
                    switch(j) {
                    case EV_KEY: type = "keys/buttons"; break;
                    case EV_REL: type = "relative";     break;
                    case EV_ABS: type = "absolute";     break;
                    case EV_MSC: type = "reserved";     break;
                    case EV_LED: type = "leds";         break;
                    case EV_SND: type = "sound";        break;
                    case EV_REP: type = "repeat";       break;
                    case EV_FF:  type = "feedback";     break;
                    }
                    printf(" %s", type);
                }
            }
            printf("\n");
            close(fd);
        }
    }
 
    if (argc > 1) {
        sprintf(name, "/dev/input/event%d", atoi(argv[1]));
        if ((fd = open(name, O_RDWR, 0)) >= 0) {
            printf("%s: open, fd = %d\n", name, fd);
            for (i = 0; i < LED_MAX; i++) {
                event.time.tv_sec  = time(0);
                event.time.tv_usec = 0;
                event.type         = EV_LED;
                event.code         = i;
                event.value        = 0;
                write(fd, &event, sizeof(event));
            }
            
            while ((rc = read(fd, &event, sizeof(event))) > 0) {
                printf("%-24.24s.%06lu type 0x%04x; code 0x%04x;"
                       " value 0x%08x; ",
                       ctime(&event.time.tv_sec),
                       event.time.tv_usec,
                       event.type, event.code, event.value);
                switch (event.type) {
                case EV_KEY:
                    if (event.code > BTN_MISC) {
                        printf("Button %d %s",
                               event.code & 0xff,
                               event.value ? "press" : "release");
                    } else {
                        printf("Key %d (0x%x) %s",
                               event.code & 0xff,
                               event.code & 0xff,
                               event.value ? "press" : "release");
                               
                    }
                    break;
                case EV_REL:
                    switch (event.code) {
                    case REL_X:      tmp = "X";       break;
                    case REL_Y:      tmp = "Y";       break;
                    case REL_HWHEEL: tmp = "HWHEEL";  break;
                    case REL_DIAL:   tmp = "DIAL";    break;
                    case REL_WHEEL:  tmp = "WHEEL";   break;
                    case REL_MISC:   tmp = "MISC";    break;
                    default:         tmp = "UNKNOWN"; break;
                    }
                    printf("Relative %s %d", tmp, event.value);
                    break;
                case EV_ABS:
                    switch (event.code) {
                    case ABS_X:        tmp = "X";        break;
                    case ABS_Y:        tmp = "Y";        break;
                    case ABS_Z:        tmp = "Z";        break;
                    case ABS_RX:       tmp = "RX";       break;
                    case ABS_RY:       tmp = "RY";       break;
                    case ABS_RZ:       tmp = "RZ";       break;
                    case ABS_THROTTLE: tmp = "THROTTLE"; break;
                    case ABS_RUDDER:   tmp = "RUDDER";   break;
                    case ABS_WHEEL:    tmp = "WHEEL";    break;
                    case ABS_GAS:      tmp = "GAS";      break;
                    case ABS_BRAKE:    tmp = "BRAKE";    break;
                    case ABS_HAT0X:    tmp = "HAT0X";    break;
                    case ABS_HAT0Y:    tmp = "HAT0Y";    break;
                    case ABS_HAT1X:    tmp = "HAT1X";    break;
                    case ABS_HAT1Y:    tmp = "HAT1Y";    break;
                    case ABS_HAT2X:    tmp = "HAT2X";    break;
                    case ABS_HAT2Y:    tmp = "HAT2Y";    break;
                    case ABS_HAT3X:    tmp = "HAT3X";    break;
                    case ABS_HAT3Y:    tmp = "HAT3Y";    break;
                    case ABS_PRESSURE: tmp = "PRESSURE"; break;
                    case ABS_DISTANCE: tmp = "DISTANCE"; break;
                    case ABS_TILT_X:   tmp = "TILT_X";   break;
                    case ABS_TILT_Y:   tmp = "TILT_Y";   break;
                    case ABS_MISC:     tmp = "MISC";     break;
                    default:           tmp = "UNKNOWN";  break;
                    }
                    printf("Absolute %s %d", tmp, event.value);
                    break;
                case EV_MSC: printf("Misc"); break;
                case EV_LED: printf("Led");  break;
                case EV_SND: printf("Snd");  break;
                case EV_REP: printf("Rep");  break;
                case EV_FF:  printf("FF");   break;
                    break;
                }
                printf("\n");
            }
            printf("rc = %d, (%s)\n", rc, strerror(errno));
            close(fd);
        }
    }
    return 0;
}

  
 
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147

按下电源按键之后,最终实践发现是event2,可以监听到key code以及按键的动作;

	...
	/dev/input/event2: open, fd = 3
Thu Mar 21 21:38:28 2019.801129 type 0x0001; code 0x0074; value 0x00000001; Key 116 (0x74) press
Thu Mar 21 21:38:28 2019.801129 type 0x0000; code 0x0000; value 0x00000000; 
Thu Mar 21 21:38:28 2019.801159 type 0x0001; code 0x0074; value 0x00000000; Key 116 (0x74) release
Thu Mar 21 21:38:28 2019.801159 type 0x0000; code 0x0000; value 0x00000000; 
Thu Mar 21 21:38:35 2019.038000 type 0x0001; code 0x0074; value 0x00000001; Key 116 (0x74) press
Thu Mar 21 21:38:35 2019.038000 type 0x0000; code 0x0000; value 0x00000000; 
Thu Mar 21 21:38:35 2019.038028 type 0x0001; code 0x0074; value 0x00000000; Key 116 (0x74) release
Thu Mar 21 21:38:35 2019.038028 type 0x0000; code 0x0000; value 0x00000000; 


  
 
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11

文章来源: great.blog.csdn.net,作者:小麦大叔,版权归原作者所有,如需转载,请联系作者。

原文链接:great.blog.csdn.net/article/details/88726932

【版权声明】本文为华为云社区用户转载文章,如果您发现本社区中有涉嫌抄袭的内容,欢迎发送邮件进行举报,并提供相关证据,一经查实,本社区将立刻删除涉嫌侵权内容,举报邮箱: cloudbbs@huaweicloud.com
  • 点赞
  • 收藏
  • 关注作者

评论(0

0/1000
抱歉,系统识别当前为高风险访问,暂不支持该操作

全部回复

上滑加载中

设置昵称

在此一键设置昵称,即可参与社区互动!

*长度不超过10个汉字或20个英文字符,设置后3个月内不可修改。

*长度不超过10个汉字或20个英文字符,设置后3个月内不可修改。